; B5US-1.INS - US Robotics S100 modem insert for BYE5 - 07/17/85
;
;	     US Robotics S100 modem Interface routines
;
;	     Note:  This is an insert, not an overlay.
;
;		*********************************
;		*				*
;		*   DOES NOT SUPPORT 2400 BPS	*
;		*				*
;		*********************************
;
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
; 07/17/85  Modified for use with BYE5		- Irv Hoff
; 03/11/85  Adapted to BYE331			- Joe Wright
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
; Port equates
;
PORT	EQU	0C0H		; Modem data port
MDCTL1	EQU	PORT+1		; Status port and control port #1
;
;
; Bit functions
;
BDIV64	EQU	04FH		; 8 data bits, no parity, 1 stop, div 64
BDIV16	EQU	04EH		; 8 data bits, no parity, 1 stop, div 16
BRESET	EQU	040H		; Reset 8251A
;
BANHI	EQU	035H		; Answer phone, RTS high (300/1200 baud)
BANLOW	EQU	015H		; Answer phone, RTS low  (110/600 baud)
DTR	EQU	002H		; DTR bit in command word for off-hook
				;   control
;
;-----------------------------------------------------------------------
;
;
; See if we still have a carrier - if not, return with the zero flag set
;
MDCARCK:IN	MDCTL1		; Read port
	ANI	80H		; Check DSR for carrier detect
	STA	CARFLG+1	; Remember it
	RET
;.....
;
;
; Return previous carrier status
;
CARFLG:	MVI	A,0		; Immediate value set by MDCARCK
	ORA	A		; Set the flags
	RET
;.....
;
;
; Disconnect and wait for an incoming call
;
MDINIT:	CALL	MDCARCK		; Do we have a carrier?
	JZ	IMINIT		; No carrier, initialize the modem
	CALL	MDRESET		; Hang up
	JMP	MDINIT		; Try it again
;.....
;
;
;Input a character from the modem port
;
MDINP:	IN	PORT		; Get character
	RET
;.....
;
;
; Check the status to see if a character is available.	If not, return
; with the zero flag set.  If yes, use 0FFH to clear the flag.
;
MDINST:	IN	MDCTL1		; Read port
	ANI	02H		; Check receive ready bit
	RZ			; Return if no character
	ORI	0FFH
	RET
;.....
;
;
; Send a character to the modem
;
MDOUTP:	OUT	PORT		; Send it
	RET
;.....
;
;
; See if the output is ready for another character
;
MDOUTST:IN	MDCTL1		; Read port
	ANI	01H		; Check transmit ready bit
	RET
;.....
;
;
; Reinitialize the modem and hang up the phone by dropping DTR and
; leaving it inactive.
;
MDQUIT:	CALL	IMQUIT		; Tell modem to shut down
;
MDSTOP:	RET
;.....
;
;
; The following routine sets the baudrate.  BYE5 asks for the maximum
; speed you have available.
;
SET2400	EQU	$
;
SETINV:	ORI	0FFH		; Make sure the zero flag isn't set
	RET
;.....
;
;
; The pairs of XCHG instructions in the following code are to allow
; for the reported slowness of the 8251a command/status port.
;
; Note:  Asserting DTR during 8251 initialization will hang up the phone.
; To keep the phone off-hook if carrier is present, DTR is asserted or
; not, depending on the last condition of the carrier detect flag.
;
MDRESET:CALL	INITUSR		; Initialize the modem and hang up
	MVI	A,BDIV16	; 1200 bps
	OUT	MDCTL1
	XCHG
	XCHG
	MVI	A,BANHI+DTR	; Put phone on-hook
	JMP	SENBAUD
;
SET300:	CALL	INITUSR		; Initialize Robotics
	MVI	A,BDIV64	; Set mode and divide by 64 (300 baud)
	OUT	MDCTL1
	XCHG
	XCHG
	CALL	CARFLG		; Data carrier detect
	MVI	A,BANHI		; Set RTS high (300 baud)
	JNZ	ST3		; If carrier, leave phone off-hook
	ORI	DTR		; Otherwise leave it on-hook
;
ST3:	JMP	SENBAUD
;
SET1200:CALL	INITUSR		; Initialize Robotics
	MVI	A,BDIV16	; Set mode and divide by 16 (1200 bps)
	OUT	MDCTL1
	XCHG
	XCHG
	CALL	CARFLG
	MVI	A,BANHI		; Set RTS high (1200 bps)
	JNZ	SENBAUD
	ORI	DTR
;
SENBAUD:OUT	MDCTL1		; Send the command byte
	XCHG
	XCHG
	CALL	DLP		; Let the modem settle down for 1 second
	XRA	A		; Clear flags to indicate good baud
	RET			;   change
;.....
;
;
INITUSR:XRA	A
	OUT	MDCTL1
	XCHG
	XCHG
	OUT	MDCTL1
	XCHG
	XCHG
	OUT	MDCTL1
	XCHG
	XCHG
	MVI	A,BRESET	; Send reset code to 8251
	OUT	MDCTL1
	XCHG
	XCHG
	XRA	A		; Says baudrate change was ok
	RET
;....
;
;			       end
;-----------------------------------------------------------------------